Sunday, March 18, 2007

Wi-fi Wireless Internet Made Simple

Wi-fi Wireless Internet Made Simple


Just what is all this Wi-Fi wireless internet stuff they are trying to confuse and torment me with?

It is actually quite simple, useful and most of all convenient.

All you probably want to do is to share your internet connection throughout your home whether it be to other computers or so that you can sit in your bedroom and wirelessly surf the internet or send email. Perhaps as well you wish to share files such as songs throughout the computers in your house, apartment or condo.

Don’t let them confuse with all this alphabet soup - b , g , a , 11 megabytes , 54 , 108.

To begin with most any of the systems are beyond overkill. All will go faster than the even high speed broadband internet. Most use the same frequency as the standard cordless phones (2.4 GHz). . Be reassured the phones and the wireless internet in most cases will co- exist and work well with each other.

The most common wireless setups wireless b and g use the frequency most cordless phone use. G wireless internet is sort of a faster b standard. What is important to know is that it is all standardized. B will work with G and G products will work with B. G is said to up to 5 times faster than B that is assuming that you are relatively close. G wireless is very useful primarily if you are sharing large files between computers. For ordinary browsing b wireless is still overkill speed, faster as said than most broadband internet connections. The usual stated range of these wireless products is 300 feet indoors range and 1000 feet outside. The range is basically line of sight. Heavy dense objects – primarily metal, metal doors, metal foil insulation, heavy bricks and pipes and objects such as furnaces, metal filing cabinets will block reception to some degree. As well if the manufacturer makes some ultra high speed claims remember that both the router and wireless network adapters will have to be that brand and that special computer networking hardware feature to work at those high speeds and transmission rates. Remember to that wireless internet transmission speeds fall rapidly with distance.

Wireless internet is basically a radio setup with a transmitter and receivers. The transmitter is a box that plugs into the internet to share your internet connection. This is called a “Router “. . Wireless routers are made by a number of manufactures and the most widely known are the Linksys and D-Link brands. All routers are fairly good now. Tech support may be something to consider for setup ease. Routers are often sold on sale at big box stores as a means of drawing customers who already have at least one computer into their stores. It is reasoned that if a customer wants to buy a router the odds are good that he or she has more than one computer and once in the store will make additional purchases .Perhaps they will be even so fed up with the older computer as the kids have taken use of the newer faster model that the customer will even buy a additional new computer from the store.. The routers that you will find on sale will most likely be the newer g standard routers which will work with your B or G wireless network adapters in your computers.


In order to find all of the article and other information please refer to this page
  • Wi-fi Wireless Internet Made Simple-- i want to finish reading! Click here

  • Enjoy! Mike!
    Be sure to check out some of the rest of our site at
  • Computerz101- Free Computer Help & More
  • Thursday, March 8, 2007

    HOW TO INSTALL A MOTHERBOARD!

    Hell today were going to talk about HOW TO INSTALL A MOTHERBOARD!

    How To Install A Motherboard

    (Important make sure you read through this guide before you begin installation of your new motherboard.)

    The motherboard is the largest and one of the most important components of your computer. It’s reliability and health is utmost important.

    Once you have picked out and purchased your motherboard you are ready for installation.

    Carefully remove the motherboard from the box, do not remove it out of the ESD (electro static discharge) bag. Do a quick inventory to make sure you have all of your parts. Most likely you should have all of you IDE cables for the hard drive and cdrom, and possibly I/O plate. If you purchased a motherboard that support ATA hard drives you should have those cables.

    Once you have verified that you have all the parts, pick up the user manual, and read through it, you don’t have to read it from cover to cover but you want to familiarize yourself with the motherboard, in addition many motherboard manufactures will also include a quick installation guide so take a look at that also.

    Now you are ready, your work area should be clean and static free. Put on your anti static wrist band, if you have one. A anti static wrist band is just basically a cloth wrist band that has a snap on stretchable cable that is grounded, the grounded surface area helps keep electrostatic discharge in control.

    Remove the motherboard from the box and all of the parts. Then remove the motherboard from ESD bag and lay it inside the empty box. Cut open your ESD bag on each side and turn it inside out so that you can lay your motherboard inside of it. Just laying your new motherboard on top of your ESD bag is not enough protection from electro static discharge.

    Prepare your computer chassis. If you have already installed and mounted your power supply, tie the power cords out of your way with some wire ties, or some Velcro. You need a clear path from the opening of your chassis to the bottom of your chassis, where your motherboard will be mounted.

    Something’s you need to think about before you drop your new motherboard into your chassis is, cooling. Depending on what type of processor you have purchased, the processor may run hot. So you have to think about good ventilation for your chassis. Heat can destroy your new investment in a matter of hours. If you do not already have at least two exhaust fans on your chassis you may have to think about actually cutting a hole either at the top of your chassis or on the side to mount the exhaust fans. Ok pick your jaw off the ground; it’s not as bad as it sounds. If you have a dremel with a cutting blade it can be very easy. Use an old CD as a template and draw around the CD with a washable marker. Then just follow the line with your dremel. Now you don’t have to do this, you can buy a chassis with plenty of exhaust fans already installed, so that is something to consider when you are in the process of buying all of your parts.

    Now let’s get back to installing your new motherboard. Once you have a clear path to the bottom of your computer chassis, make sure that you have your bag of screws handy, and a long neck Philips screw driver. Take a look at the motherboard mounts, they are installed inside your chassis, these are the mounts that you will align with the holes on the motherboard. If you do not have any mounts you will have to installed them your self. The hardware should have come with your chassis if your chassis is new; if not make sure you save your screws, when you remove your old mother board.

    Remove the old I/O plate and install the new one, take a look at the manual for reference. Make sure that it is secure. Look at the mounts that are on the bottom of your, chassis you want to make sure that you line up the mounts with the holes that are drilled on your mother board. (Important DO NOT DRILL ANY HOLES IN YOUR MOTHERBOARD) Angle the motherboard so that I/O ports will match with the holes on the I/O plate. There is a good chance that you might need to remove the break away pieces of metal the cover some I/O holes on the I/O plate. It is a good idea to check for proper match before installing the mother board.

    As you angle the motherboard towards the I/O plates make sure that mounting holes on the motherboard are lining up with the mounts on the chassis. Gently push the motherboard towards the back of the chassis so that the I/O ports are snug against the I/O plate, and that all of the ports are protruding all the way out.

    Once you have the motherboard correctly align with the I/O plate you are ready to mount the motherboard to the chassis with the screws provided. Tighten each screw down so that they are snug; do not over tighten the screws.

    Use the manual as your guide and connect the power LED, speaker, reset switch ECT, coming off of the chassis to the F_panel (Front Panel) of your motherboard. Since each motherboard will be slightly different make sure to refer to the manual for exact instruction.

    Ok well there you have it. You just installed your new motherboard.

    To read more computer related articles, get free software and e-books go to
  • Computerz101- Free Computer Help & More
  • Thanks for coming. Mike!

    Friday, March 2, 2007

    Web SIte Security- 8 Tips

    Web Site Security: 8 Tips

    The computer age has made the personal computer affordable for most people of virtually every industrialized country. Whether it takes the form of a desktop or laptop, all computers are used for a wide variety of functions. As the number of people on the Internet soars ever higher, security becomes an increasing concern. Here are some tips to help ensure a personal or business Web site is secure against attack.

    In order to find all of the 8 tips and other information please refer to this page
  • The 8 Tips i want to read! Click here

  • Enjoy! Mike!
    Be sure to check out some of the rest of our site at
  • Computerz101- Free Computer Help $ More
  • Thursday, March 1, 2007

    How to Start Video Blogging?

    Free Computer Help

    How to Start Video Blogging?

    Videoblogging is the next generation of posting ideas and products over the internet. Everybody knows about textblogging. Now they use videos for a better way of expression. This form of communication may entail a lot of resources, but it is all worth it. If pictures say a thousand words, videoblogging exceeds that by far.

    A videoblog requires larger disk spaces on websites, a faster server, and a whole new set of programs to support it. Videoblogs can be fed through RSS. This is technology of syndicating your website to other RSS aggregators.

    Videoblogging works with people on the internet expressing their selves. Now if you put this on a business prospective, you are up to a lot of benefits. Think of it as a powerful tool in making showing your prospective customers your line of products or your services. It’s just like showing a commercial all for free. And if you videoblog through RSS, then most probably you are getting your target market.

    People like to see what they are going to buy. Some would like to see proof and be sure that they are getting their money’s worth before shelving their dimes on it. All of us know the influence of a thirty second commercial. The effect of videoblogging is similar to that. You show your product, people watch it. If they like it, they buy it. If you present it good enough, they’ll buy the product even if they don’t need it.

    Now on the web, things are pretty much static, unlike in television in which all are moving. If you post something that is mobile, it would most likely catch attention. Now imaging your product parading in all it’s royalty through videoblog. You’ll get phone call orders in no time.

    If your business is just starting up, you can create a videoblog right at your own home. All you need is your web camera, microphone, video software, and lights. For as long as you know how to use your camera, then you can create a videoblog.

    Invest in a good web camera. The higher its resolution is the better the output. And you like to present your goods in the optimum way so get the best one possible. Make a short story, or just capture your goods in one go. Just make sure you are getting the best profile for each. Get those creativity juices flowing.

    Lights are important in a production. Make sure you illuminate entirely the area you are going to use to create videoblog. The brighter the area, the crispier the images will be. You can also use lighting effects for added appeal to the presentation.

    Should you require sounds for your videoblog, you need a microphone. Record you voice as a voice over for promoting the product and its benefit to consumers. Sounds are as important as videos on a videoblog. It is advisable to make your sound effects as enticing as the video.

    Your video editing software can be any program. You need this to finalize your work. You can add sounds, delete some bad angles, or insert some still pictures in there too. Some programs are user-friendly and can be used even with zero knowledge on video editing. Even simple video editing programs should do the trick. Select your background carefully too. The light affects the presentation so make sure that the background and the light complements each other.

    Videoblogging is a great tool but it also has it downside. It may slow down the computer so other may steer clear of it. Download time may also be time consuming especially if customer is still on a dial- up connection.

    But don’t let those stop you. Let videoblogging be an alternative for you, though it is best to still keep the text and pictures present in your presentation to accommodate all possible viewers of your site.

    Nowadays, the more creative you are in presenting your product to the market, they more you are likely to succeed. Videoblogging offers an interactive way of selling. You involve the customers. You instill in them the advantage of your goods. And at times, those are enough to make a sale.

    Here are a couple website to get you started on your journey.

    http://www.vidblogs.com/

    Setup a free video blog here
    http://www.freevlog.org/

    Enjoy. Thanks. Mike!

    Need any further Information go to http:///www.computerz101.com to contact me.